ford explorer rear end gear ratio

The ring gear measures 88 inches in diameter with the single-piece case bolted with 10 716X20-inch threaded bolts. Rear Wheel Drive 4 Door 16 mpg city 21 mpg hwy.

Usa Standard Ring Pinion Gear Set For Ford 8 8in In A 3 73 Ratio Zg F8 8 373 In 2021 Gear Sets Pinion Gear Ford Explorer Xlt

This chart applies to all Ford non-overdirve transmissions manual and automatic.

. 308 327 355 373 410. Axle Type - Rear. Fourth Gear Ratio 1.

Axle codes for Ford Explorer Ranger and Bronco II. The most common gearing for rear differential in Ford Explorer SUVs includes the following. Second Gear Ratio 1.

Axle Capacity Gear Ratio Year Vehicle. RPM - Rear End Ratio Chart. You will see the word AXLE and a two-digit code.

A 355 axle ratio is standard on 44 manual XLS 44 XLT Eddie Bauer and Limited models. 308-to-1 327-to-1 331-to-1 355-to-1 373-to-1 and 410-to-1 according to Drivetrain. The following table shows the various Ford part numbers and gear ratios for the matched ring and pinion gear sets used on 1928 through 1934 Model A 103-12 WB and Model B 106 WB Ford car and commercial chassis not trucks.

As more engineering took place a varying number of ratios were developed. Axle Codes Door Sticker. Listed are the expected RPMs at 60 MPH with a given rear end ratio and tire height.

The 88-inch differential feature six gear ratios. Ford 88-Inch Axle Specifications Ring Gear Differential. 5-Inch axle with a 4.

308-to-1 327-to-1 331-to-1 355-to-1 373-to-1 and 410-to-1 according to Drivetrain. First Gear Ratio 1. The plate layouts vary depending on the.

Gear ratios depend on the year and. All USA Standard Ring and Pinion Gear Sets come with a standard one year warranty against manufacturing defects. 2007 ford mustang Gt rear axle assembly 118000 miles 88331 - 800 Liberty Complete axle assembly 88331 GT rear end assembly axle to axle other parts available 46 automatic.

The model year that you have will likely use a number of gear ratios. Transfer Case Gear Ratio high 1 NA. Rear axle codes can be found on the Safety Standard Certification label attached to the left drivers side door lock post.

0691 REAR AXLE RATIO. 308-to-1 327-to-1 331-to-1 355-to-1 373-to-1 and 410-to-1 according to Drivetrain. The standard receiver hitch which is part of the rear frame offers.

2010 ford mustang Gt rear axle assembly 118000 miles 88331 - 800 Liberty Complete axle assembly 88331 GT rear end assembly axle to axle. ZF 5-SPEED MANUAL Diesel Gas Final Drive Ratios Axle Ratio. Use this chart to find the axle ratio that corresponds to that code.

Power is transmitted from the transmission to rear end 11 in high gear. The 88-inch differential feature six gear ratios. 308 327 355 373 410.

This Rear diff can be configured with either a 355 or 373 gear ratios and has an open differential to match the stock configuration of your Explorer SUV. These types of set ups were not limited. In some cases both an A and a B prefix part number are shown for a particular gear set.

Towing capacity is increased with Explorers V-8 engine. In the early 1990s Ford started of light with the 40 liter Cologne engine. A 373 axle ratio and limited slip differential are standard with the Class IIIIV towing package.

And looking at the axle tag above you can see its a 373 gear ratio with a limited slip in a 88 inch axle. Third Gear Ratio 1. The axle that I believe is 410 had 5W140 Synth Oil Only on the metal tab bolted into the diff cover.

Rear Axle Ratio Non-Limited Slip Explorer 331 3A 358 3B 373 3C Automatic Transmission MAXIMUM LOADED TRAILER WEIGHT lbs Axle GCWR lbs EXPLORER Engine Ratio RWD 4WD RWD4WD 23L EcoBoost 1 3000 10000 210100 53002. Gear ratios depend on the year and model of the Ford vehicle. The chart below may be of some help in deciding what rear end ratio is right for you.

32-mm stabilizer bar. Rear Axle Gear Ratios. Axle Codes Door Sticker.

Axle Capacity - Front lbs. Independent short- and long-arms SLA architecture with coil-over shocks. The most common gearing for rear differential in Ford Explorer SUVs includes the following.

Ford cars and trucks from 1968 on have an axle code on the Certification Plate information on this plate can be used to determine if you vehicle is factory equipped with a limited slip positraction rear end - differential. Axle Capacity - Rear lbs. RPM - Rear End Ratio Chart.

The certification plate can be located on the lock face of the left door edge. 1999 Ford Explorer Eddie Bauer 4dr 112 WB Trim Info.

Ford 7 5 8 8 Inch Axle Tag Door Codes The Ranger Station